BPL

cone crusher lubricant system names   1.Pressure Gauge (Lubrication- Line 1) 2.Gauge isolator (Lubrication-Line1) 3.Pressure Gauge (Lubrication - Line 2) 4.Gauge isolator (Lubrication - Line 2) 5.Pressure Gauge (Adjusting) 6.Gauge isolator (Adjusting) 7.Pressure Relief Valve - Line 1 8.Manifold block -Line 1 9.Pressure Relief Valve -Line 2 10. Manifold block - Line 2 11. Manual Valve (Adjusting) 12. DC Valve 13. Door limit Switch 14. Relief Valve (Adjusting) 15. Return Oil Level Gauge 16. Tank Oil Digital Temperature Indicator 17. Tank Oil Digital Temperature Indicator 18. Return Oil Digital Temperature Indicator 19. Increasing, Push Button with lamp 20. Lock for Increasing & Decreasing 21. Decreasing Push Button with lamp 22. Filter Clog Switch 23. Low Pressure Switch 24. Return Temp Sensor 25. Filter Clog Switch 26. Low Pressure Switch 27. Drive Motor (Adjusting) 28. Oil Filter 29. Temperature Sensor (Tank Oil) 30. Manifold Block 31. Temperature Sensor (Tank Oil) 32. Tank Oil...

 BEFORE STARTING Remove any latches, brackets, gadgets, and many others. Used for shipping and take a look at the condition of the crusher. Ensure that the crusher is operated most effective in a secure way and best in proper mechanical condition. Operation of the crusher should handiest be allowed when all necessary protective and safety devices, e.G. Guards, emergency forestall devices, silencers, aspirators etc. Are in location and in operating circumstance. Before beginning the crusher, make sure that there aren't any men and women inside the vicinity whose safety might also be endangered! Walk around the crusher and ensure that there's nobody on, through or beneath the crusher. Warn anybody within the region earlier than beginning. Ensure that the crusher cavity is empty. Start the lubricating device (1) of the crusher and take a look at the function of protection gadgets for oil pressure, oil temperature, and oil glide. Bleed air from the adjusting device before starting ...

●What is Force? In material science, power is a quantitative portrayal of a connection that causes an adjustment of an item's movement. Power is a vector amount, with both heading and extent. It is characterized as Mass x Acceleration = Force. The SI unit of power is the newton (N); characterized as the unit of power which would provide for a mass of one kilogram a speed increase of 1 meter each second squared. There are a ton of power types including pressure, pressure, shearing, twisting, and rubbing. Newton's Universal Law of Gravitation expresses that any two articles apply a gravitational power of fascination on one another. The gravitational speed increase of earth is characterized as g＝9.80665m/s2 (standard worth) by International Committee of Weights and Measures. For instance, the heaviness of 1kg mass at earth is almost equivalent to 1(kg)×9.8(m/s2)＝9.8(N).

Estimation OF TORQUE Force is characterized as the power which will in general change the straight movement or-olatie pt a body: It might likewise be characterized as the tiring &r Twisting snapshot of a power with regards to a hub. Force is given as: (7.15) T= FD where, T= force F= power D - opposite separation from the hub of turn of the line of activity of the power Fundamentally, there are two sorts of force sensors accessible for the estimation of force on process machines: (©) in-line turning force sensors (I) in-line fixed force sensors. Response force sensors, for example those that action the force on a machine hous- ing rather than on a shaft, are for the most part not appropriate for process estimation since associating power and line lines influence the deliberate force. In-line Rotating Torque Sensor The in-line turning force sensor is utilized for the force estimation of pivoting types of gear.

VRIBETOR SCREEN MAINTENANCE CHECK LIST 1c heck and ensure without plugin screen meshes daily . 2.check the meshes and clamping bars ,ensure it is tight and are not wom too thin - weekly. 3.inspect all the bolt to see if they are tight -daily. 4.check the screen for proper cleaness between it and structure including the chutes-weekly. 5.check the condition of the motor  base for crackes and proper tightness-daily. 6.check the spring and make sure they are not brocken-monthly. 7.check the height of the spring any ensure all are equal -monthly. 8.check that the bolt are tight and are adjusted equaily-daily. 9.check the feed to the screen ,is it centered flowing on to the chute-weekly. 10.check the chute and gates for wear are build up-daily. 11.check the amplitude leveland it is constant value at all sides -weekly. 12.apply the grease 50 grams per bearing in every -100hrs. 13.check the propeller shaft protection cover bolts are tight -weekly. 14.check the screen frames for wear crack ...

  CONE CRUSHER    A cone crusher is a compression type of machine that reduces material by squeezing or compressing the feed material between a moving piece of steel and a stationary piece of steel. CONE CRUSHER MAINTENANCE CHECKING INTERVALS G.P CONE (GENERAL PERFORMANCE) 1.GREASE FILLING SPIDER BEARING 12 HRS. 2.CHECK OIL LEVEL IN RESERVOIR 8 HRS. 3.CHECK CONDITION OF CABLES AND COMPONENTS 8 HRS. 4.CHECK THE DISCHARGE AREA TO ENSURE IT IS OPEN AND UNOBSTRUCTED 8 HRS. 5.CHECK THE CONDITION OF LINERS LOOK FOR CRACKS AND VERYTY THICKNESS 8 HRS. 6.CHECK AND ENSURE TIGHTNESS OF HYDRAULIC CONNECTIONS CHECK AND ENSURE PROPER V-BELT 24 HRS. 7.CLEAN AIR BREATHERS 24 HRS. 8.GREASE FILLING PRIMARY DUST SEAL 100G-100HRS. 9.CHECK AND ENSURE FLOAT SWITCH OPERATION 100 HRS. 10.CHECK /CLEAN STAINER AND MAGNETIVE PLUG 500 HRS  \11.OIL FILTER CHANGE 500 HRS . 12.LUBRICATION OIL CHANGE 500 HRS MAXIMUM 1500 HRS . 13.COUNTER SHAFT OIL CHANGE 500 HRS . 14.RETIGHTE CYLINDER COVER  B...

 JAW CRUSHER SPARE NAME: 1.DETECTOR PLATE 2.JAW PLATE 3.JAW CLAMPING BAR 4.JAW SUPPORTING BAR 5.REAR END FRAME 6.CHEECK PLATE 7.PITMAN 8.FLY WHEEL 9.SIDE PLATE 10.TOGGLE BEAM 11.WEDGE ASSEMBLY 12.TOGGLE SEAT 13.RETRACTION SPRING 14.TOGGLE PLATE  15.

 आज हम आपको गिट्टी कैसे बनता है ए बताएंगे आपको, ए गिट्टी कंस्ट्रक्शन काम के लिए बोहोत जरूरी है बिल्डिंग लाइन और रोड प्रोजेक्ट के लिए बोहोत मेहतापुर्नो रोल है, ए नहीं होगा तो हमारा क्या हाल होगा एकबार सोचकर देखो, ए पत्थर हिन्दुस्थान का हर जगह नहीं मिलती है ए इंडस्ट्री है मध्य प्रदेश, झारखंड, महाराष्ट्र, गोआ, गुजरात, कश्मीर, केरला, कर्नाटका, तमिलनाडु, और भी कुछ जगह में है। ए विश्व संसार में उपोर वाला का दिया हुआ बोहोत कुछ है उसके अंदर हम लोग आज पत्थर के बारे में जानेंगे , ए जिधर पत्थर से गिट्टी का रूप देता है उस इंडस्ट्री को स्टोन क्रेशर प्लांट बोलता है। इसको गिट्टी का रूप देने के लिए बोहोत प्रोसेस है-- १। खदान - पत्थर से गिट्टी का रूप देने के लिए रॉ मेटेरियल का आवश्यकता है, ए रॉ मेटेरियल जिधर से आता है उसको हिंदी में खदान बोलता है। इधर बोरा साइज पत्थर को ड्रिलिंग कोरके उसके अंदर डेटोनेटर और मैग्जीन के सोहायोता से ब्लास्टिंग किया जाता है ए ब्लस्टिंग भी बोहोत टाइप का होता है आप लोग कॉमेंट कोरेगा तो ब्लस्तिंग के उपर और एक आर्टिकल लिखूंगा। ब्लस्टिग के बाद चोता चोटा पत्थर का रूप दिया जात...

In order to make use of the rocks or ores obtained through quarrying/explosion in the Mining and Construction sectors, the materials need to be crushed to reduce them to a smaller size. We call this process  CRUSHING. Out put primary section minimum 90 mm to maximum 300 mm  It depends on how many tph plant